minibike-forum.nl

*geen sponsor* Racing Team schreef:Mensen die gast is niet spaans kijk de 1e paar plaatjes op de 1e pagina zie je 1 scooter met een geel kenteken en zwarte leter in spanje rijden de scooter met een wit kenten ik weet ckr dat in spanje wit kenten met zwarte leters is maar ik denk alemaal dat hij gewoon nederlands is....



M.v.G...Mikey..Minibikey..

Whats Your Point ?!

Niet zeuren, Als hij nou nederlands is zou hij de vragen toch gewoon nederlands stellen ?

en over de nummerbord plaatje ; Zien de plaatjes er in nederland dan wel zo uit ? Think clearly mister minibikey.


Sorry For The Overlast..

Please single I can translate English and the Spanish. I cannot read what written ace.

Does nobody help me?

they said that you are a Hollander and the ather one said you are a Spanish men.
But I know that you are a Spanish men.
Because you said that somewhere in this topic
your bike is very nice!!

That is "Hollander"?

A Netherlands Person

We are called "hollanders" because we live in "Holland"

For that to say that I am from Holland?

I AM SPANISH AND LIVE IN SPAIN.

Yesterday modify the chassis, the motorcycle.
Now it(he,she) is mas short, measures 73 cm of axis(axle) to axis(axle)..



That to think of the measurements that and position(place) mas arrives?

Hi


really don't want to dissapoint u!!


but..


i think u didn't solve ur problem by replacing the rear sprocket...

u just created a new one....

the rear sprocket is mounted way to far from the tire...

u can't take fast left turns like this....trust me...had the same problem...!

the max for mounting the sprocket from the rim is aprox..40mm


u better think it over before finishing the framework...



Greetings

Wim

You since(as,like) do I solve the problem?

That it(he,she) recommends to me to do?

Hi again



i't not that i want to tell u what to do...just like to avoid a lot of frustration..


What normally is done....building a bike with an engine like this..

Build the engine.....done...good job though!!

buy ur parts...........done that too...not to cheap materials..u got a lot of power with this engine!

mount ur engine and parts on a setup like ur (steel table, easy welding, love it)

align the engine, wheels, fork, exaust...etc..

u could set ur rearsprocket a little closer to the tire...with another engine (like puch) is that an option....with u it isn't!

u really can't, if u like to drive this bike in a normal way, replace the rear sprocket the way u did....just leave it where it is..

make sure that every part is in place....also ur carburater and airfilter,
u really don't want to finish ur framewrok, and not be able to place ur carburator /airfilter (bin there!!)(very frustrating)
the radiator is alway a problem to put it in place...just leave enough space for it....(just try if it fitts once in a while, while welding ur framework)


important items....seen from the back side..!!

wheels exactly in line
make sure that the front fork stand vertical...
and set thet front and rear sprockets exact in line...

the engine itself now isn't in line with the wheels...
no problem....even impossilble!
i'vv never seen a minibike with the engine in line with the weels.
the bike simply is to small for that!!
the idea of mis-balance with ur engine not in line with ur wheels
is just the idea....u won't even notice it!! (every bike with an Puch engine,
has the engine really hanging out of the framework, the empty space is filled with exaust, trust me, we'r not falling over because of the mis-balance)


then u build ur frame around all this...easier said then done...


really hope u got some idea's!!


Greetings from holland

Wim

my problem is that the block is very wide.

then to be able to align the wheels and the block, I must put back the chassis very wide.

not putting the supplements in the wheel, the block is thus:



putting the supplements in the wheel, the block is thus:



I think that you are right at the time of curving in the highway.

I cannot think like solving it.

I cannot think like making the block + small.


Thank you very much by the aid.

here to be able to see that I am Spanish.



Here to be able to see that it leaves very ugly the chassis to me. He is very fat.













And already tired to me.
I am not going to finish.
Everything goes to the sweepings.
I close this post.

WOOOTTTT NOOOO

Thats not good make this project finished then sell it for a price.Gehehehehehe

But cant you take another exhaust